Return to Archer Airguns Tube Cap for Umarex Fusion and Xisico XS60C
Sort By::
Page of 1


  0 of 0 people found the following review helpful:
 
3 of 5 Cap replacement for Umarex fusion August 9, 2018
Reviewer: Jojo Afable from California  
I purchased mine from you over five years or so ago. The problem I encountered with mine was that the second 12 g CO2 remained intact unpunctured. So I don’t get the full benefit of double 12g CO2. Can it be fixed? It should puncture it on the first fire, right?

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
5 of 5 Great Repair Part! November 13, 2017
Reviewer: Leonard Cogar, LC Air Rifles from Sheffield Village, OH United States  
I bought this for a client's Umarex Fusion Co2 rifle while repairing it. With a little secret sauce or Pellgun Oil on the seal, it cured all the finicky nonsense involved with the factory one! You no longer have the Co2 bleed-off screw with this one. But that was the problem with the factory gas tube cap. Just buy this one and you won't have any more problems sealing it up. And place one drop of oil on the tip of each Co2 cartridge too.

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
5 of 5 Great design March 15, 2016
Reviewer: Anonymous Person from Beaver Falls, PA United States  
I used this in my Umerax Fusion. Installed easily and worked great. So much easier than playing around with the factory tube cap.

Was this review helpful to you?

  2 of 2 people found the following review helpful:
 
4 of 5 So much better than the factory cap March 3, 2015
Reviewer: Stan Henry from Claremore, OK United States  
I ordered this because the factory cap on my Fusion had a tendency to leak.  After trimmer the stock just a bit, the new plug fit great and sealed up nicely!  I would recommend this to anyone that is having issues with the factory cap.
I would have given it 5 stars if I didn't have to trim my stock for it to fit.

Was this review helpful to you?

  2 of 2 people found the following review helpful:
 
5 of 5 Doesnt leak like OEM one does March 2, 2014
Reviewer: Geoffrey Kroll from Greenwood, IN United States  
I tried many things to keep the OEM endcap from leaking out co2.  the best I could get was 5 days before my co2 would be gone.

Picked up this endcap and NO LEAKS.  I did add a washer to the internals to get a better puncture on the co2 carts as 1 of them was barely pierced.  With the thin washer added to the internals I get a nice clean hole in both carts.

the only downside is, you have to shoot out all the co2 to get the endcap off, unlike the OEM with bleeder where you can vent the last little bit.

I am happy with my purchase and would recommend it to any who are having leak issues on their Fusion

Was this review helpful to you?

  2 of 2 people found the following review helpful:
 
4 of 5 Tube Cap Alignment December 8, 2013
Reviewer: Victor Wilson from San Tan Valley, AZ United States  
I just received your replacement Cap. When I went to install. I could only get it to just start to thread on when it felt like it was cross threading. it kept getting tighter with only a couple of Threads on. I thought Bad Threads. I quickley disassembled new Cap. Took the Threaded piece installed. Threads were perfect. I put it back together but left it real loose. threads went on no problem. I then tightened up phillips screw. un-threaded. finished tightening screw . re-installed . threading and fit were perfect after that. no problem. My conclusion is you should make sure the center piece of cap is centered into the Bore. before you crank the cap all the way down.

Was this review helpful to you?